Adding a new printer integration previously not covered


#1

Please follow this template:

*This is a wiki post, meaning any user [trust level 1][1] or higher can contribute.*
*If you are not yet tl1 or have a question/comment/concern, please post below.*

##PREPARING THE "PRINTER"
What needs to be done to get at the electronics, tip, or firmware of your machine

##WIRING THE DISCOV3RY
[Img] Where to access the electronics board containing the extruder motor driver(s).
Connector, cable, or wiring steps necessary for integration to electronics board.
Wiring schematic. What are the matching colour wiring pairs for the Discov3ry stepper motor compared to your printer? (Black, Green, Blue, Red pair with what?
[Img] The exact location of the connection for the extruder motor driver.
Please note all extra steps for wiring here if the integration for your 3D printer is more involved.  

###FIRMWARE UPDATES
Describe any firmware changes necessary for the integration process.  This could include settings like disabling the cold extrusion code, adjusting the EEPROM settings for the Discov3ry (typically ~10-100x default settings), hard coding XYZ offsets for a new nozzle, etc.

###GCODE UPDATES FOR DISCOV3RY
What are the ideal slicer parameters that you have found for a specific material? Layer height, speed, infill, etc. Please share a configuration file that you have successfully utilized, preferably using the slicer that is applicable to your 3D printer.

###MOUNTING THE DISCOV3RY TIP
[Img] The mounting system you have utilized (link to .stl file if applicable)
Other hardware needed in the mounting process (Links to McMasterCarr are golden)
[Img] How to install the mount on the 3D printer (Include Tools required)
[Img] How to attach Discov3ry tip to the mount. (Is it adjustable? Any other special features that should be known?)

###OTHER
Are there any special procedures for bed levelling to avoid breaking the tip or bed plate?

###FINAL PICTURES
[Img Gallery] Successful prints – test prints or otherwise.
[Img] Printer and Discov3ry integrated together

###LINKS
A link to the Manufacturers specifications page
A link to the forum community for the Printer/Manufacturer

  [1]: http://forum.structur3d.io/t/welcome-to-structur3ds-forum/6

About the integration category
#2

#3

Will look like this:


This is a wiki post, meaning any user trust level 1 or higher can contribute.
If you are not yet tl1 or have a question/comment/concern, please post below.

##PREPARING THE “PRINTER”
What needs to be done to get at the electronics, tip, or firmware of your machine

##WIRING THE DISCOV3RY
[Img] Where to access the electronics board containing the extruder motor driver(s).
Connector, cable, or wiring steps necessary for integration to electronics board.
Wiring schematic. What are the matching colour wiring pairs for the Discov3ry stepper motor compared to your printer? (Black, Green, Blue, Red pair with what?
[Img] The exact location of the connection for the extruder motor driver.
Please note all extra steps for wiring here if the integration for your 3D printer is more involved.

###FIRMWARE UPDATES
Describe any firmware changes necessary for the integration process. This could include settings like disabling the cold extrusion code, adjusting the EEPROM settings for the Discov3ry (typically ~10-100x default settings), hard coding XYZ offsets for a new nozzle, etc.

###GCODE UPDATES FOR DISCOV3RY
What are the ideal slicer parameters that you have found for a specific material? Layer height, speed, infill, etc. Please share a configuration file that you have successfully utilized, preferably using the slicer that is applicable to your 3D printer.

###MOUNTING THE DISCOV3RY TIP
[Img] The mounting system you have utilized (link to .stl file if applicable)
Other hardware needed in the mounting process (Links to McMasterCarr are golden)
[Img] How to install the mount on the 3D printer (Include Tools required)
[Img] How to attach Discov3ry tip to the mount. (Is it adjustable? Any other special features that should be known?)

###OTHER
Are there any special procedures for bed levelling to avoid breaking the tip or bed plate?

###FINAL PICTURES
[Img Gallery] Successful prints – test prints or otherwise.
[Img] Printer and Discov3ry integrated together

###LINKS
A link to the Manufacturers specifications page
A link to the forum community for the Printer/Manufacturer